How Do I Setup and Reset My Netgear Extender?

3 min read
netgear

A Netgear WiFi range extender can be useful in many ways to boost your existing WiFi signals up to 30 percent. You need to get connected to Netgear_ext and configure your extender in order to get the most out of it.

In the event that your Netgear extender stop working suddenly and you can’t make the most out of its WiFi signals, reset it back to factory default settings.

Here’s how to reset Netgear extender.

To reset your Netgear WiFi range extender, follow the step-by-step instructions outlined underneath:

Step 1: First and foremost, disconnect your Netgear extender from your existing router (if connected).

Step 2: Ensure that your Netgear extender is receiving continuous power supply from its respective wall outlet during the reset process.

Step 3: Once you’re done, locate the reset hole on your Netgear WiFi range extender.

Step 4: Take a pin, paper clip or any thin object and insert it into the Netgear extender’s reset hole.

Step 5: Hold the reset hole on your Netgear extender for a couple of seconds and release it.

Kudos! You have successfully reset your Netgear WiFi range extender.

Now, to make your Netgear extender up and running, you need to set it up. Don’t know how to setup Netgear extender? Well, need not to panic! We’ve got you covered! Just follow the step-by-step Netgear extender setup listed below, make your device up and running, and get the internet range in every nook and cranny of your house.

Here are the steps to configure your Netgear WiFi range extender.

To setup Netgear extender, follow the steps highlighted below in exact given order:

Step 1: Supply your Netgear WiFi range extender a continuous power supply.

Connect your Netgear extender to your router using an Ethernet cable.

Step 2: Check the power LED on your Netgear extender. It must be green and stable.

Step 3: Turn on a WiFi-enabled device, connect to Netgear_ext, hover your mouse cursor over the browser’s address bar, and type www.mywifiext.net.

Step 4: New Extender Setup page displays.

Step 5: Walk through the on-screen instructions and setup Netgear extender in a hassle-free way.

That’s it! You have successfully configured your Netgear WiFi range extender using www.mywifiext.net. On the off chance if the web address does not work for you, use http://192.168.1.250 IP address.

Found the Netgear extender setup steps a provided above a bit tricky? Don’t sweat over it! We’ve got your back! Try the easiest Netgear extender WPS setup method to configure your device without any hassle.

Here’s how setup Netgear extender using the WPS method:

If your existing router consists of the WPS button then you can go with this method. In case not, then configure your Netgear extender manually by following the steps given above. And if the Netgear extender manual method is spinning your head, you can contact our technical executives anytime.

Configure Your Netgear Extender Using the WPS Method

Step 1: Right off the bat, power on your Netgear extender.

Step 2: Let the power LED on your extender become green and stable.

Step 3: Do not forget to place your Netgear extender and router in close proximity.

Step 4: Locate the Netgear extender WPS button.

Step 5: As soon as you found the Netgear extender WPS button, push it.

Step 6: When the WPS LED on your Netgear extender start blinking, push the WPS button on your router as well.

Step 7: The WPS LED on your router will start blinking too upon pushing the button.

Wow, you did it! You have successfully setup Netgear extender using the WPS setup method. Now, you can connect your devices to Netgear_ext and enjoy surfing the internet to the fullest.

Leave a Reply